Emerald Spa DS-4 Manuál s instrukcemi

DS3 SERIES Object detection and measurement light grid INSTRUCTION MANUAL

Instructions manual DS series 7 It is thus important to position the light grid according to the minimum distance from any reflecting sur

DS series Instructions manual 8 NO YES YES 2.2.3. Installation of several adjacent light grids When several devices must be installed in

Instructions manual DS series 9 Fig. 3 3. MECHANICAL MOUNTING The emitting and receiving bars must be installed with the relevant sens

DS series Instructions manual 10 4. ELECTRICAL CONNECTIONS The electrical connection between the emitter and receiver units is made through

Instructions manual DS series 11 4.1. Notes on the connections For the correct functioning of the AREAscanTM . light grid, the following

DS series Instructions manual 12 • The AREAscanTM are NOT safety devices and so MUST NOT be used to control the safety of the machines wh

Instructions manual DS series 13 5. FUNCTION SELECTION The functions implemented in the AREAscanTM devices can be selected using the dip-

DS series Instructions manual 14 Table 1 indicates the type of function and the relative position of the dip-switches. Tab. 1 NOTE: The d

Instructions manual DS series 15 6. CALIBRATION PROCEDURE The calibration procedure sets the signal level that arrives from the receiver

DS series Instructions manual 16 7. FUNCTIONING MODE The DS3 light grid is a detection and measurement device and thus the beam interru

DATASENSOR S.p.A. Via Lavino 265 4005 0 Monte S. Pietro - Bolog na - Italy Tel: + 39 051 676 561 1 Fax: + 39 051 6759 3

Instructions manual DS series 17 • Scanning with CROSSED beams: where several photoreceivers are illuminated by the beam of a single ph

DS series Instructions manual 18 7.2. Measurement mode 7.2.1. Absolute mode (see functions 5 and 6 of Tab.1 at page 14) Provides the measur

Instructions manual DS series 19 7.2.2. Relative measurement (see function 7 of Tab.1 at page 14) Provides the measurement of the dimensi

DS series Instructions manual 20 7.3. Detection mode (teach-in) The teach-in mode can be selected using the dip-switches (see functions 9

Instructions manual DS series 21 The following operating modes can be selected using the dip-switches: 7.3.1. Absolute detection (see fun

DS series Instructions manual 22 7.3.2. Relative detection (see function 10 of Tab.1 at page 14) The digital output (PNP) switches each tim

Instructions manual DS series 23 7.4. DARK/LIGHT mode of the output ( see functio n 1 3 and 1 4 of Tab .1 at pag e 14) Defines th

DS series Instructions manual 24 8. DIAGNOSTIC FUNCTIONS 8.1. Visualisation of the device status The operator can verify the operating sta

Instructions manual DS series 25 8.2. Fault and diagnostic messages The operator can verify the device functioning status and the stop o

DS series Instructions manual 26 8.2.2. Error mode RECEIVER UNIT Signal Cause Check and Repai r - PNP output does not switch. - Devic

DS series Instructions manual INDEX 1. GENERAL INFORMATION ...

Instructions manual DS series 27 9. CHECKS AND P ERIODICAL MAINTENANCE The following is a list of recommended check and maintenance oper

DS series Instructions manual 28 10. TECHNICAL DATA Po wer su ppl y: 24 V dc ± 15% Consu mpti on of emit ter u nit (TX): 100 mA m a

Instructions manual DS series 29 11. LIST OF AV AILABLE M ODELS Model Length of sensitiv e area Length of controlled area N°. beams Re

DS series Instructions manual 30 12. OVERALL DIM ENS IO NS All the dimensions given are in mm. RECEIVER EMITTER

Instructions manual DS series 1 1. GENERAL INFORMATION 1.1. General description of the AREAscanTM light g ri d The AREAscanTM light gr

DS series Instructions manual 2 Some parts or paragraphs of this manual containing important information for the operator are preceded by a

Instructions manual DS series 3 1.3. Typical applications The following images supply an overview on some of the main applications. Ob

DS series Instructions manual 4 2 INSTALLATION MODE 2.1. Precautions to be observed for the choice and installation of the device • The d

Instructions manual DS series 5 2.2. General information on the device positioning • Place the device near the detection area. • Ali

DS series Instructions manual 6 2.2.2. Minimum distance from reflecting surfaces Reflecting surfaces placed near the light beams of the A